Abstract cedar and water design

Arctic Spa Arctic Fox Specs, Dimensions and Manual

The Arctic Spa Arctic Fox is a Custom Series hot tub that measures 85 × 69 × 39 in (217 × 174 × 98 cm), holds 208 US gal (787 L), has 2 molded seats, and is listed for up to 4 people.

Arctic Spa Arctic Fox dimensions and capacity

Series Custom Series
Model status Current model
Dimensions 85 × 69 × 39 in (217 × 174 × 98 cm)
Water capacity 208 US gal (787 L)
Empty weight 611 lb (277 kg)
Filled weight 2,346 lb (1,064 kg)
Seats 2
Maximum capacity 4
Loungers 1
Jet options 30 or 15
Pump options up to 2

The filled weight does not include people, steps, accessories, or snow. Have a qualified professional check any deck or raised platform before placing a filled spa on it.

Which Arctic Fox specs does this guide cover?

The specs on this page are for the Arctic Fox shown in Arctic Spas’ May 2026 brochure. Arctic Spas has used the Arctic Fox name for more than one model year, so an older tub may have different dimensions, water capacity, seating, or equipment. Check the serial plate and the manual that came with your spa before ordering a cover, pump, heater, or other year-specific part.

Arctic Fox seating and layout

The Arctic Fox has 2 molded seats and room for up to 4 people. It has one lounger. This is a compact 7-by-6-foot model with one lounger, two molded upright seats, and capacity for four.

If you are comparing models, pay attention to the footwell and lounger setup as much as the advertised capacity. A tub may technically hold the listed number of people but still feel tight once everyone is in it.

Jets and pump packages

Depending on the package and model year, the Arctic Fox was offered with 30 or 15 jets and up to 2 pumps. Check the equipment label inside your cabinet before ordering a pump, heater, control panel, or electrical part.

Why the package matters: The 15-jet Prestige package uses one pump and the 30-jet Signature package uses two. The current brochure and manual cap Arctic Fox at two pumps; copied three- and four-pump lines on one web page should not be used.

Electrical requirements for the Arctic Fox

240V wiring method 240V fixed wiring from the GFCI spa panel: Line 1, Line 2, neutral, and equipment ground
Published feeder-wire guidance 6-gauge wire is listed in the 2026 Arctic Spas table; the manual does not specify one universal insulation type, conductor material, or raceway
GFCI breaker 1 pump: 40A GFCI; 2 pumps: 50A GFCI
Published equipment input 1 pump: 32A actual; 2 pumps: 40A actual
Heater 5,500W on 240V; certified 115V version uses 1,000W
Plug N Play Available as a 120V Plug N Play upgrade in the May 2026 brochure
Plug-in electrical details Plug N Play is the one-pump package: 115V, 12A actual, 15A breaker, and 14-gauge wire in the 2026 manual. Use the factory cord and match the receptacle to the certification label.
Spa disconnect At least 5 ft (1.5 m) from the water, readily accessible, and within sight; within sight is generally no more than 50 ft under NEC terminology
Bonding conductor At least No. 8 AWG solid copper to the local bonding grid in the United States, as required by the Arctic Spas manual and local code

Breaker box and disconnect location: Arctic Spas says the GFCI disconnect must be readily accessible and visible to the hot tub occupant, but at least 5 ft (1.5 m) from the water. Under common NEC terminology, within sight generally means visible and within 50 ft, but the adopted code edition, amendments, product listing, and local inspector control the exact placement. The enclosure installed near the spa is commonly called the spa disconnect, GFCI spa panel, or spa subpanel.

Wiring and bonding: Arctic Spas requires a licensed electrician and local inspection. The certification label beside the controller determines the final voltage, actual load, breaker, and approved configuration. Where Arctic publishes a feeder gauge, it is shown in the model table; conductor insulation, terminal material rating, raceway, run-length adjustments, and local requirements still belong to the electrician. The manual calls for the spa bonding lug to connect to the local bonding grid with at least No. 8 AWG solid copper in the United States or No. 6 AWG stranded copper in Canada. Nearby metal equipment, enclosures, water pipe, conduit, and metal surfaces within 5 ft may also require bonding.

Plug-in configurations: Plug N Play is the one-pump package: 115V, 12A actual, 15A breaker, and 14-gauge wire in the 2026 manual. Use the factory cord and match the receptacle to the certification label. The manufacturer’s 5 ft appliance warning is not a complete receptacle-placement rule. Receptacle spacing, GFCI protection, cord length, and Plug N Play placement depend on the product listing and the NEC/CEC edition adopted locally.

Other electrical safety: The North American supply must include a suitable GFCI breaker that opens all ungrounded conductors. The load neutral must connect directly to the GFCI as shown in Arctic Spas’ licensed-electrician diagram. Never bypass the GFCI. The manual says no electrical appliance such as a light, phone, radio, or television may be within 5 ft (1.5 m) of the hot tub. Accessible controls or devices must meet the manual’s low-voltage and local-code requirements.

Do not size the circuit from jet count alone. Pump count, heater size, optional SDS equipment, controller programming, and model year can change the required service. The certification label beside the spa controller is the final authority. Arctic Spas requires this work to be completed by a licensed electrician and approved under local code.

Will the Spa Filter Adapter fit the Arctic Fox?

Our Spa Filter Adapter Kit v3 may fit a Arctic Fox, but only when the tub is a 2020 or newer Custom Series with the matching Pro Filter and skimmer setup. The model name alone is not enough because Arctic Spas has reused several model names over the years. Before ordering, compare your filter area with the photos and checklist in our compatibility guide.

For any replacement filter, compare the cartridge height and diameter, the top and bottom openings, the thread style, and the space inside the filter housing. Those details matter more than the name printed on the side of the tub.

Arctic Fox manuals and drawings

These links point to Arctic Spas’ official model pages, manuals, brochures, and technical drawings:

The files stay on Arctic Spas’ website, so you will always be viewing the manufacturer’s copy rather than a PDF we downloaded and reposted.

Compare the Arctic Fox with other Arctic Spa models

See every current and older Arctic Spa model in the main hot tub guide.

More help for Arctic Spa owners

Arctic Spa Arctic Fox FAQs

Is the Arctic Fox a current Arctic Spa model?

Yes. The Arctic Fox is included in Arctic Spas' May 2026 hot tub brochure.

What are the Arctic Fox dimensions?

The Arctic Fox measures 85 × 69 × 39 in (217 × 174 × 98 cm). Before ordering a cover or building around the spa, measure your actual cabinet and check the model year on the serial plate.

How much water does the Arctic Fox hold?

Arctic Spas lists the Arctic Fox at 208 US gal (787 L). Older versions may hold a different amount, so use the manual for your year when adding water-care chemicals.

How much does the Arctic Fox weigh?

The listed dry weight is 611 lb (277 kg), and the listed filled weight is 2,346 lb (1,064 kg). People, steps, accessories, and snow add more load, so have a qualified professional check any deck or raised platform.

How many people fit in the Arctic Fox?

The Arctic Fox is listed for up to 4 people, with 2 molded seats. It has one lounger.

Where can I find the Arctic Fox manual or PDF?

Use the Arctic Spas links in the Manuals and drawings section above. Choose the document that matches your model year; a current brochure will not cover every part used in an older tub.

What electrical service does the Arctic Fox need?

The published 240V installation is 240V fixed wiring from the GFCI spa panel: Line 1, Line 2, neutral, and equipment ground. Breaker guidance: 1 pump: 40A GFCI; 2 pumps: 50A GFCI. Published wire guidance: 6-gauge wire is listed in the 2026 Arctic Spas table; the manual does not specify one universal insulation type, conductor material, or raceway. Available as a 120V Plug N Play upgrade in the May 2026 brochure. The certification label beside the controller is the final authority, and Arctic Spas requires a licensed electrician to follow local code.

Does the Spa Filter Adapter Kit v3 fit the Arctic Fox?

It may, if your spa is a matching 2020 or newer Custom Series model with the correct Pro Filter and skimmer setup. Check the filter area and model year before ordering.

These specifications come from Arctic Spas’ model pages, brochures, technical sheets, and owner manuals. Direct links are provided above. Last updated July 11, 2026.

Arctic Spas is a trademark of its respective owner. SpaFilterAdapter.com is an independent aftermarket business and is not affiliated with, endorsed by, or approved by Arctic Spas.